Skip to main content

Troubleshooting the Kisi Intercom Pro

Introduction

This guide helps you troubleshoot and resolve common issues with the Kisi Intercom Pro 2. Kisi does not manage your network setup. For advanced networking concerns (firewall rules, DHCP, VLAN settings), contact your IT department or network administrator.

Intercom not powering on

Possible causes

Power issues

The intercom might be receiving insufficient or unstable power from the PoE switch or injector. Confirm your PoE source supports IEEE 802.3af (44–57 VDC).

Network cable problems

Damaged or loose RJ45 connectors can interrupt power delivery. Using cables below Cat6 or exceeding 100 meters can also lead to power issues.

Hardware malfunction

Physical damage or internal component failures can prevent the intercom from powering on. Look for visible cracks or loose parts.

Troubleshooting steps

Step 1: Verify the power source

  • Confirm that your PoE switch or injector meets IEEE 802.3af standards.
  • If using a PoE injector, make sure the cables are in the correct ports (Data/Power Out → Intercom, Data In → Switch/Router).

Step 2: Perform a 5-minute power cycle

  • Unmanaged PoE switch: Unplug the power or remove the intercom's cable for at least 5 minutes.
  • Managed PoE switch: Disable PoE on the port for at least 5 minutes, then re-enable.
  • Manual unplug: Pull the Ethernet cable from the intercom's pigtail for 5 minutes.

Step 3: Check the network cable

  • Ensure you’re using Cat6 or higher.
  • Inspect for any damage or loose connectors.
  • Keep the cable run under 100 meters.

Step 4: Isolate the intercom

  • Connect the intercom to a known-working PoE switch or injector.
  • Try a different port or a new Cat6 cable to rule out a bad port or cable.

Quick checklist: intercom not powering on

  • PoE source is IEEE 802.3af-compliant (44–57 VDC)
  • Front LED is off, confirming no power indicator
  • Attempted a 5-minute power cycle
  • Cable is Cat6 or better, undamaged, and under 100 m
  • Tested a different PoE port or injector

Intercom has power but offline

Possible causes

DHCP server and network settings

The intercom may not be obtaining a valid IP address if there are DHCP conflicts or misconfigurations.

Firewall or security restrictions

Ensure that necessary traffic is allowed in your network rules.

Faulty hardware ports

A defective port on the router, PoE switch, or injector can prevent proper data flow.

Damaged or loose RJ45 connectors

Physical cable damage or poor connector terminations can degrade or block network signals.

Inadequate Ethernet cable type/length

Using cables below Cat6 or exceeding 100 meters can cause signal loss or connectivity drops.

Troubleshooting steps

Step 1: Confirm DHCP and network settings

  • Verify that your router (or other DHCP server) is active and the intercom is on its client table list
  • Ensure the following are allowed:
    • ICMP (ping)
    • AWS servers
    • NTP servers: time.windows.com, pool.ntp.org, time.nist.gov

Step 2: Power cycle the intercom

  • Unplug the Ethernet cable for 5 minutes, then reconnect. This prompts a fresh IP request.

Step 3: Ping test

  • Successful ping: The intercom is on the network but may be blocked from reaching the cloud (e.g., firewall rules).
  • Failed ping: The intercom may not have a valid IP or there’s a hardware/cable issue.

Step 4: Examine cable and connectors

  • Swap in a known-working cable and port.
  • Use a PoE tester or cable tester if available.

Step 5: Reset the intercom

  • Locate the reset button on the back of the intercom. Using a pin, press and hold the button for 15 seconds.
  • Release the reset button when the light turns green.
  • The light will start blinking blue
  • The light will turn off
  • The light will return to a steady blue, indicating normal operation.

Quick checklist: Intercom has power but offline

  • Verify intercom's status via web dashboard
  • Confirm DHCP and network settings
  • Check security/firewall restrictions
  • Perform a 5-minute power cycle
  • Ping the intercom's IP to confirm network visibility
  • Try a different cable or PoE port if there’s no response
  • Reset the intercom

Need more help?

Contact Kisi support

Remember to provide detailed information:

  • Intercom's Device ID
  • Logs, screenshots, or videos of the issue
  • Your network setup details (if applicable)
  • Steps you have already taken

Including these details helps Kisi support diagnose the problem more quickly and accurately.